✨ Military Tools List
2422
THE NEW ZEALAND GAZETTE.
[No. 99
APPENDIX 29—continued.
TOOLS FOR ARMOURERS—continued.
| Description. | Quantity allowed. | Remarks. |
|---|---|---|
| Tools— | ||
| Adjusting, fore sight, R.S.M.L.E.— | ||
| Cramps .. .. .. | 1 | |
| Punches .. .. .. | 2 | |
| Clearing ‘303 in. arms— | ||
| Bits—Screw .. .. .. | 1 | |
| Spoon .. .. .. | 1 | |
| Bushes, bit, screw .. .. | 1 | |
| Rods, No. 2 .. .. .. | 1 | |
| Extractor spring .. .. | 1 | |
| For alteration of cocking-pieces, R.S.M.L.E.— | ||
| Broaches .. .. .. | 2 | |
| Taps .. .. .. | 3 | |
| Tools, recessing .. .. | 1 | For R.S.M.L.E., Mark III and converted Mark IV. |
| Removing—Handguard, No. 1 .. .. | 1 | Mark I and Ix and converted Mark II and IIx. |
| Plate, keeper, screw wind-gauge, R.S.M.L.E. | 1 | |
| Striker, R.S.M.L.E. .. .. | 1 | |
| Wad, stock-bolt .. .. | 1 | Mark I and IIx and converted Mark II and IIx. |
| Sight line, R.S.M.L.E.—No. 1 .. .. | 1 | Mark III and converted Mark IV. |
| No. 2 .. .. | 1 | For Mark II box only. |
| Vice, parallel, regimental armourers’ .. | 1 | |
| Section 7. | ||
| Awls, handles, brad, small .. .. | 2 | |
| Chisels, firmer—¾ in. .. .. | 1 | |
| ½ in. .. .. | 1 | |
| ¼ in. .. .. | 1 | |
| Files— | ||
| Bastard—Flat, 6 in. .. .. | 2 | |
| Half-round, 6 in. .. .. | 2 | |
| Round, 8 in. .. .. | 1 | |
| Square, 8 in. .. .. | 1 | |
| Fine cut, hand, safe edge, tanged—10 in. .. | 2 | |
| 8 in. .. .. | 2 | |
| Regular cut, half-round—10 in. .. | 2 | |
| 8 in. .. .. | 1 | |
| Saw, taper, second cut, single—6 in. .. | 2 | |
| 3 in. .. .. | 2 | |
| Second cut—Half-round, 4 in. .. | 2 | |
| Round, 4 in. .. .. | 2 | |
| Smooth—Flat, 6 in. .. .. | 1 | |
| Half-round—8 in. .. .. | 1 | |
| 6 in. .. .. | 2 | |
| 4 in. .. .. | 1 | |
| Hand, safe edge—8 in. .. .. | 2 | |
| 4 in. .. .. | 1 | |
| Pillar—6 in. .. .. | 2 | |
| 3 in. .. .. | 1 | |
| Round, 4 in. .. .. | 2 | |
| Three-square, 4 in. .. .. | 1 | |
| Dead-smooth, half-round, 6 in. .. | 1 | |
| Gimlets, twist, Nos. 2, 3, and 5 .. | 5 | |
| Gouges, handled, firmer—¾ in. .. | 1 | |
| ½ in. .. .. | 1 | |
| ¼ in. .. .. | 1 | |
| Hammers, riveting—24 oz. .. .. | 1 | |
| 4 oz. .. .. | 1 | |
| Handles, file—Large .. .. | 6 | |
| Small .. .. | 6 | |
| Holders, file, with handle, half-round—10 in. .. | 1 | |
| 8 in .. .. | 1 | |
| Irons, soldering, tinman’s, small .. | 1 | |
| Pliers, flat nose (pairs) .. .. | 1 | |
| Rasps, second cut, half-round, 9 in. .. | 1 | |
| Saws, hand, 23½ in. .. .. | 1 | |
| Stocks, drill, hand, Mark II .. .. | 1 | |
| Vices, hand, 16 oz. .. .. | 1 | |
| Section 27. | ||
| Cartridges, small - arm, dummy, ‘303 in., inspectors | 20 | Mark IV for units in possession of rifles altered to suit Mark VII ammunition; Mark III for other units. |
Next Page →
Online Sources for this page:
VUW Te Waharoa —
NZ Gazette 1917, No 99
NZLII —
NZ Gazette 1917, No 99
✨ LLM interpretation of page content
🛡️
Tools for Armourers
(continued from previous page)
🛡️ Defence & MilitaryTools, Armourers, Rifles, Weedon Section, Repair